Grindmaster 380 TX tracked stump grinder on a studio background

8 views — tap a thumbnail to enlarge.

In stock — ships crated from our UK warehouse

Grindmaster 380 TX Stump Grinder

A 412 kg tracked grinder with a 16″ carbide wheel and a walk-beside handset — narrow enough for back-garden access, heavy enough to take a 900 mm stump out to 300 mm below grade.

£3,449 ~~£4,299~~ SAVE 20%

Includes UK VAT & mainland delivery. Finance from £81/month.

Offer ends in

00DAYS

00HRS

00MIN

00SEC

Cutter wheel406 mm (16″)

Engine38 hp V-twin petrol

Width760 mm

Weight412 kg

Reserve yours — £3,449

Secure checkout is handled by our sales team — no card details are taken on this site.

Free deliveryUK mainland

30-dayreturns

2-yearwarranty

760 mm across the tracks — clears a standard side gate
16″ wheel with 12 reversible carbide teeth
Grinds to 300 mm below grade and 560 mm above
Radio handset: you stand clear of the wheel, not over it
Hydrostatic track drive climbs a 30° bank
412 kg — moves on a car trailer, no HGV needed

Built for the job

Why this grinder gets into gardens others can't

760 mm across the tracks

The single spec that decides most domestic jobs. It clears a standard side gate and a terrace alleyway without lifting fence panels.

Radio handset

You work beside the machine, not behind the wheel. Better sightlines on the cut and you are out of the debris arc.

Carbide teeth, bolt-on

Twelve reversible teeth. Turn them once for a fresh edge, then swap in minutes with the spanner in the crate.

Tracks, not wheels

Low ground pressure keeps it off a customer's lawn and lets it climb a 30° bank to a stump a wheeled machine cannot reach.

412 kg

Light enough for a braked car trailer. No plant lorry, no HGV hire, no waiting for a transport slot to start a job.

Hydraulic swing

Sweeps the wheel across a 1010 mm arc, so a 900 mm stump comes out without repositioning the tracks.

Full specification

Grindmaster 380 TX technical data

Model	BranchForge Grindmaster 380 TX
Engine	V-twin OHV petrol, 764 cc
Rated power	38 hp (28 kW)
Starting	Electric with recoil back-up
Fuel capacity	24 litres
Cutter wheel diameter	406 mm (16 inches)
Teeth	12 reversible carbide, bolt-on
Cutting depth below grade	300 mm
Cutting height above grade	560 mm
Cutting width per sweep	1010 mm
Drive	Hydrostatic, independent track control
Maximum gradient	30 degrees
Travel speed	0–4.2 km/h
Control	Proportional radio handset, 25 m range
Track width	180 mm rubber
Overall width	760 mm
Overall length	1.94 m
Overall height	1.18 m
Operating weight	412 kg
Noise level	104 dB(A) at operator position
Warranty	2 years parts, 1 year engine (manufacturer-backed)

Specifications are nominal and may vary by production batch.

Questions

About the Grindmaster 380 TX

Will it fit through my customer's side gate?

760 mm across the tracks. A standard UK side gate opening is 780–900 mm, so it fits the great majority. Measure the narrowest point — usually the gate post, not the gate itself.

How deep will it grind?

300 mm below grade in a single setup, which is enough to re-turf or re-lay a patio over. For a stump you intend to build on, plan on excavating the root plate as well; a grinder removes the stump, not the root system.

Petrol or diesel — why petrol here?

At this weight, petrol gives the best power-to-weight ratio, and 38 hp on a 412 kg chassis is what keeps it under the gate-width limit. A diesel of the same output would add roughly 70 kg and 100 mm of width.

What does a set of teeth cost to replace?

A full set of twelve reversible carbide teeth is £186 including VAT from our UK stock. Reversing them first typically doubles the life, so most operators buy one set a season.

Can I hire it out to make it pay?

Owners do, but check your insurance first — most standard tool policies exclude hire to third parties. We supply the manual and a handover checklist; the liability is yours.